clay paky alpha beam manual

Disimballo e predisposizione - Unpacking and preparation. Installazione e messa in funzione - Installation and start-up. Pannello di controllo - Control panel - Panneau de controle. Steuerpult - Pannel de controlIt is essential to know the information and comply with the instructions given in thisCLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons deriving from installation, use and maintenance that have not been carriedCLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instruction manual at any time and without prior notice.Make sure the point of anchorage is stable before positioningThe safety chain must be properly hooked onto the fitting andIf the safety chain gets used, it needs to be replaced with aThe projector needs to be positioned so that the objects hit byThe projector must be positioned so that any flammable materialsIt is permissible to mount the fitting on normally flammableFor the fitting to operate well and reliably, the ambient. The fitting is protected against penetration by solid bodies of overConnection must be made to a power supply system fitted withConnection to the electricity mains must be carried out by aCheck that the mains frequency and voltage correspond to thoseThis label also gives the input power to which you need to refer toThe maximum temperature that can be reached on the external. Before starting any maintenance work or cleaning the projector,After switching off, do not remove any parts of the fitting for atIf it is necessary to replace the lamp, waitThe fitting is designed to hold in any splinters produced by a lampThe fitting mounts a high-pressure lamp that needs an externalThis product contains a rechargeable lead-acid battery. ToInstructionsThe products referred to in this manual conform to the. European Community Directives to which they are subject:La conoscenzaLa ringraziamoClay Paky!

• clay paky alpha beam 300 manual, clay paky alpha beam 700 manual, clay paky alpha wash 1200 manual, clay paky alpha wash 575 manual, clay paky alpha beam 1500 manual, clay paky alpha wash 700 manual, clay paky alpha wash 300 manual, clay paky alpha wash 1500 manual, clay paky alpha beam manual, clay paky alpha beam manual pdf, clay paky alpha beam manual download, clay paky alpha beam manuals, clay paky alpha beam manual instructions, clay paky alpha beam 300 manual.

It is essential to know the information Menu setting CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons deriving from installation, use and Maintenance maintenance that have not been carried out in conformity with this instruction manual, which must always accompany the fitting. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base. Do not use microphone cable or other cable with characteristics differing from those specified. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512). OPTION DEFAULT Lamp DMX Invert Pan Invert Tilt Swap Pan-Tilt Encoder Pan-Tilt Color mixing Color mixing curve Curve 1 Fixed Wheel Shortcut Shutter on error Dimmer on Shutter Power Mode 4-700 Full fan speed Display. Colour Beam 1) Press to return to the top menu level. Gobo 2) Use the UP and DOWN keys to select the required test. 3) Press to confirm the selection or LEFT to keep current settings. Opening the head covers - Fig. 10. Closing the head covers - Fig. 11. ALPHA BEAM 7. WARNING: do not touch the lamp s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth. WARNING: Before using personalised gobos contact Clay Paky.Insertion of the effect modules: Repeat the operations indicated in Fig. 20 and 21 in reverse order. Informazioni di sicurezza - Safety information.

When it is in the restDuring menu setting status, after a wait time (about 1 minute) without any key having been pressed, the display automaticallyIt should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the ENTER key will be cancelled.Red. Rouge. Rojo. RotLeuchtet, wenn das Signal DMX vorhanden ist. Blinks if the DMX signal is not present. Blinkt, wenn das Signal DMX fehlt. Non usato. Not used. Nicht belegt. No utilizada. Is lit when the display is in the setting phase. Leuchtet, wenn sich das Display in der Einstellphase befindet. Is off when the display is in the rest mode. Ist ausgeschaltet, wenn sich das Display in Ruhestellung befindetTo activate this function, press UP and DOWN buttons simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will beSetting the projector starting address - Fig. 9. On each projector, the starting address must be set for the control signal (addresses from 1 to 495) considering that each Alpha Beam 300 occupies max 18 channels. The address canSetting the address:For a quick access to a parameter’s minimum value or to the first item of a menu, press the UP button while holding down the DOWN button.For a quick access to a parameter’s maximum value or to the first item of a menu, press the DOWN button while pressing the UP button.If ENTER is not pressed no settings will be confirmed. The Help function. The projector has a Help function that can be used to display a short description of any menu item. To activate the Help function, press the ENTER key and keep it pressed while pressing UP or DOWN duringThe Help message can be displayed again by simply releasing the ENTER key and then pressing it again. Setting addresses and options with the projector disconnected.

Clay Paky,Paky range,LeggereWe thankIt is essentialCongratulationsmade with totalCarefullyGB manual. S.p.A.S.p.A. reservesClay Paky!Lire attentivemenSie daranWert gelegtPaky - aufS.p.A. se. Paky! WirBenutzung durch eineBenachrichtKompliment Produkts - wie beiSachanleitung jederzeit und ohneVoraussetzuDaten. Die BedienungsBedienungs. Lesen Sie n und die strikte lehnt jede HaftungBenutzungS.p.A.Informatione. Installation, vor, die in derDie Firma. Este producto,Die FirmaPaky y graciasLas informacioneLea atentamenteCLAY PAKY to no conformes el derecho de modificar,The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.Connecting to the control signal line (DMX) - Fig. 6. Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120.Do not use microphone cable or other cableA terminating plug must be inserted into the. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display. Clay Paky. Alpha Beam 300. Partial lamp time xxx. Total life time xxx. Address xxx. On conclusion of resetting in the case of the absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel (Fig. 7) has a display, LEDsThe display can be in one of two conditions: rest status and setting status.

The lamp remains off when the projector is turned on. A u t o. Auto DMX. The lamp turns on when a DMX signal is connected (alwaysIt turns off if there is no DMXEnable lamp control dmx channel. Used for enabling lamp remote control channel.E n c. Enable encoderS h E r. Shutter on errorDma x. D o f f. S e t. S e t 1. S e t 2. S e t 3. S e t 4. F a c t. DMX levels memory. Used for saving current channel levels. Channel levels can beDisplay max. Used for displaying at maximum brightness.Display Off. Used for automatically turning off the display after about 20Set user setting. Used to save four different settings of the items in the optionsFactory settings. Used for restoring default values on all options menu items andOption. DmxMFulC. RainOff. Off. Vect. On. OnDefault. ShDi. DiSh. Lon. PwUp. Option. Default. OnShDi. OffUsed for displaying projector operating hours (total and partial).T o t l. Total counter. Counts the number of projector working life hours (fromP a r t. Partial counter. Counts the number of partial projector working life hours sinceSELECT to go to the top menu level. Hours counter for lamp. Used for displaying the lamp working hours (total and partial).H r P r. T o t l. P a r t. Counts the number of projector working hours with the lamp onPartial counter. Counts the number of lamp working hours since the last resetSELECT to go to the top menu level. Lamp strikes. Used for displaying the number of times the lamp was turnedT o t l. Counts the number of times the lamp was turned on (fromP a r t. Counts the number of times the lamp was turned on since theSoftware versions. Used for displaying the software versions of eachSELECT to return to the top menu level. Hardware versions. Used to display the hardware version of the “Brd0” boardHw A: Type A hardware. Hw B: Type B hardware. Press SELECT to return to the top menu level. S t r k. HwB 0C y a n. M g n t. Y e l w. C o l. G o b F. Cyan filter. Magenta filter. Yellow filter. Colour wheel.

The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply. All that is needed is to press any key toOnce the required operations have been carried out, the display will switch off again after a wait time of 15 seconds.DMX startInfo. Pan. Sens. Til. HrPr. Totl. Cyan. Yelw. Par t. PTSp. Stnd. Col. Fast. GobF. HrLa. DmxM. VectSrvc. MgntPan. Tilt. Dimr. Mgnt. Par tRst. Ch 18. Ctrl. EncP. PanF. EncT. Auto. TltF. Rain. LDmx. Dly. Enc. No. ShEr. Memo. Brd2. HwB0. Dmax. Doff. Set. Set1. Fact. Set2. Frst. Set3. Set4USE OF THE SERVICE MENU (Srvc). WARNING!: Access to the Service Menu is recommended for trained technical personnel. To enable the Srvc menu press keys S and E simultaneously for a few seconds while the projector is being switched on.Pan inversion. Used for reversing Pan movement.T i l. Tilt inversion. Used for reversing tilt movement.Allows you to select the Pan and Tilt movement speed fromStnd: Standard Pan and Tilt speed. Fast: Fast Pan and Tilt speed.Dmx Modality. Allows you to select a channel arrangement from the twoUsed for reversing the CMY color mixing system.Linear Colours. Used to enable linear movement of the colour disc.Full Colour. Used to enable colour disc positioning only on solid colours.P T S p. S t n d. F a s t. Dm xM. P a n. S t n dRainbow effect. Used for enabling the rainbow effect (continual rotation ofShutter on Dimmer. Enables automatic strobe closing when the dimmer is completely closed.D i S h. Dimmer on Shutter. Enables automatic closing of the dimmer when the strobe isL o n. Lamp on mode. Used for selecting lamp lighting mode.P w U p. Power up. When the projector is turned on the lamp lights with a fixed 10D l y. Power up with delay. When the projector is turned on the lamp lights with a fixed 10The variable delay is 50ms for each channel, consequently the delay between one projector lamp lighting. N o. No lamp on.

Signal transmission cable faulty or disconnected. Incorrect addressing. Fault in the electronic circuits. Lenses or reflector broken. Dust or grease deposited.Replace the lamp. (See instructions). Replace the cables. Check addresses (see instructions). Call an authorised technician. Clean (see instructions). All prices are excluding VAT. The Alpha Beam 300 produces a super-concentrated parallel beam of light. It can be used in a similar way to a Par64 ACL, but has highly superior and innovative features. It is complete, compact and easy to maintain and install. It is the ideal “beam moving light” for professional live setups, especially long throw applications. It can penetrate the brightness of back stage washlights or LED systems with extraordinary air craft landing light effects. Professional Lighting, Entertainment products. On this page you will be able to see which transport options are available to you and at what price. You can also request a quote there. QUESTIONS ABOUT SHIPPING If you've got any questions about shipping please don't hasitate to contact us. You can do this by form, email, chat or phone. Whatever is more convenient for you. If there is anything we can help you with please tell us. Remember me No account yet. Create an Account Scroll To Top We use cookies to improve your experience on our website. By browsing this website, you agree to our use of cookies. Lea atentamente todas las partes del presente manual de instrucciones y conservelo cuidadosamente para futuras consultas. El conocimiento de las informaciones y el respeto de las prescripciones contenidas en esta publicacion son esenciales para garantizar la integridad y la seguridad de las operaciones de instalacion, uso y mantenimiento del aparato. CLAY PAKY S.p.

A declina toda responsabilidad por danos al aparato u otras cosas o personas, que derivan de su instalacion, uso y mantenimiento efectuados no conformes a lo indicado en el presente manual de instrucciones, que debera siempre acompanar al aparato. CLAY PAKY S.p.A. se reserva la facultad de modificar, en cualquier momento y sin previo aviso, las caracteristicas mencionadas en el presente manual de instrucciones. 1 Page 2 and 3: INFORMACIONES DE SEGURIDAD 1500W 10 Page 4 and 5: INSTALACION Y PUESTA EN FUNCIONAMI Page 6 and 7: 9 28 28 Inversion de la pantalla - Page 8 and 9: NOTA: En gris las programaciones po Page 10 and 11: Shutter Shutter On Error On Off SHU Page 12 and 13: Board Diagnost.Thank you, for helping us keep this platform clean. The editors will have a look at it as soon as possible.

Fixed Gobo ChangeUsed for displaying reset sensor status (On or Off ) on effects. The projector can also normally operate during sensor statusCyan. Fixed Gobo ChangeDmx monitor. Used for displaying the projector DMX channel level. TheReset projector. Used for resetting the projector.Used for turning lamp on and off from the projector controlManual control. Used for setting channel levels from the projector control panel.E n c P. Encoder Pan. Used for displaying the Pan encoder position.E n c T. Encoder Tilt. Used for displaying the Tilt encoder position.Dm x. C h 1. C h 1 8. R s tMagenta filter. Fixed Gobo ChangeMagenta filter. Fixed Gobo ChangeAutotest. Allows you to check the proper functioning of effects.Sequenza di test. Dimmer. Frost. Fixed Gobo. Test sequence. Fixed GoboP a nAllows you to adjust effects from the control panel to obtain perfect uniformity between the projectors.T i l t. D i m r. C y a n. Fixed Gobo Change. F a c tFactory settings (Fact). Allows you to restore default values of Pan (128) and Tilt (128).Pan. Testsequenz. Secuencia de test. Fixed GoboTilt. Fixed Gobo ChangeOption StndS h u tD i m rP a n FLAMP CONTROL (with option LDMX ON)Operation with option CMY OnSLOW ROTATION (0.2 rpm)FAST ROTATION (40 rpm)Operation with option Til OffOff)Operation with option Til. OnOff). Off)Off). IMPORTANT: Alpha Beam 300 is not provided with hot restrike igniterLamp OFF levels.Channel function. Pan - Tilt time. Pan - Tilt - (Pan fine - Tilt fine). Colour time. CMY - Colour wheel. Beam time. Gobo time. Fixed Gobo wheelFullDataApertura coperchi laterali - Figura 10. Chiusura coperchi laterali - Figura 11. Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the side covers - Fig. 10. Closing the side covers - Fig. 11.Lamp change - Fig 13. Take the new lamp out of its package and insert in the fitting. WARNING: do not touch the lamp’s envelope with bare hands.

Should this happen, clean the bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth. Lamp regulation - Fig. 14. To centre the lamp, turn the three adjusting screws as shown in the figure.Proceed as follows to reset the partial counts of the operating time of the projector or the lamp.The partial count of the number of times the lamp has been switched on is reset automatically when the partial counter of lamp operating hours is reset.WARNING: Before using personalised gobos contact Clay Paky.To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations areUse a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors and filters. It is recommended that the projector undergoes an annual service by aCleaning the Fresnel lens. Only use neutral soap and water to clean the Fresnel lens, then dry it carefully with a soft, non-abrasive cloth. (WARNING: the use of alcohol or any other detergent could damage the lens).Upper SideIMPORTANTE: Afferrare i moduli tramite la struttura di sostegno e non tramite particolari che potrebbero danneggiarsi. Inserimento moduli effetti: ripetere in ordine inverso le operazioni indicate alle figure 20 e 21. Extraction of the effect modules - Fig. 21. IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 20 and 21 in reverse order.Input power. Lamp. Discharge lamp with built-in power supply unit.MotorsOptical unit. Inputs. Movable bodyIP20 protection ratingCE Marking. In conformity with the European Union Low Voltage Directive. Safety DevicesCooling. Forced ventilation with axial fans. BodyWorking position. Functioning in any position. Weights and dimensionsLamp exhausted or defective.